立即使用

当前位置:首页 > 资讯

[CPRJ Direct] Circular Economy with ENGEL at K 2019

During the run-up conference held for K 2019, ENGEL unveiled its focuses of appearance at the upcoming trade show. One of these is circular economy. Dr. Stefan Engleder, the CEO of the ENGEL Group, emphasises the huge importance of this topic: “It is my personal concern to contribute to establishing a circular economy for the plastics industry, which bears a global responsibility that can only be met by companies working together. I therefore welcome the focus on circular economy at the most important international industry event. K will give this subject even more impetus.” According to Engleder, one of the priority tasks on the way to the circular economy is to open up a broader range of applications for processed plastic waste. At K 2019, five exhibits at three locations will demonstrate ENGEL's contribution as an injection moulding machine manufacturer and system solutions provider. The focus is on processing recycled material, improving process stability, and the trend towards design for recycling. Greater process stability, wider use of recycled materials “The stability of the injection moulding processes is key to being able to use recycled materials also for higher quality products,” explained Günther Klammer, Head of Plasticizing Systems division and Circular Economy expert at ENGEL. Recycled material is naturally subject to greater batch variations than virgin material. In order to significantly reduce its influence on the process, the intelligent iQ weight control assistance system will be used at ENGEL's stand to process 100% recycled ABS. The software from ENGEL's inject 4.0 program ensures a constant melt volume during injection and thus a consistently high product quality, even with strongly fluctuating raw material quality. Increasing recycled materials in sandwich-moulded components One further approach to using recycled materials more widely is sandwich components with a core of recycled material embedded in virgin material. The aim is, on the one hand, to design increasing numbers of products for this type of two-component production, while, on the other, increasing the proportion of recycled material in the sandwich structures. The proportion of recycled material that can be used in the core is essentially determined by the geometry of the moulded part and the flow pattern in the cavity. The transport boxes that ENGEL will be producing at its stand using the ENGEL skinmelt process pose a particular challenge in this respect. Despite this complex component geometry, ENGEL still succeeds in achieving a very high level of recycled content of over 50% with the skinmelt process. What is also important is the grade purity ensuring that the sandwich-moulded products can also be easily recycled at the end of their service life. ENGEL is exclusively using polypropylene for the manufacture of the transport boxes; the recycled material here originates from post-consumer collection. ENGEL collaborates with Der Grüne Punkt (The green dot), Duales System Deutschland (DSD, Germany), to this end. Considering recycling as early as in product development “Designing for recycling” means that the subsequent recycling process is taken into account as early as in the development of a new product. Further examples where this is already working well can be found in the packaging industry and in composite lightweight design. Wherever look in composite lightweight design, thermoplastic-based solutions point the way to the circular economy. In the ENGEL organomelt process, fibre-reinforced prepregs with a thermoplastic matrix such as organic sheets and tapes are overmoulded with a thermoplastic from the matrix material's material group. The entire composite component consists only of thermoplastic and glass fibres, and has the potential to be recycled at the end of its useful life. At its stand, ENGEL will be demonstrating the production-ready process with a demanding automotive application. Giving fishing nets a second life Meanwhile, in the outdoor exhibition area between Halls 10 and 16, post-consumer waste will be converted into miniature waste containers on an ENGEL victory injection moulding machine. Erema's recycling pavilion will be located in the immediate vicinity. Another victory machine will produce card boxes from recycled fishing nets there. The polyamide recycled material comes from Chile, where three American machine manufacturers have set up collection points for end-of-life nets. In Chile, the nets are recycled on an Erema system and processed into skateboards and sun glasses on ENGEL injection moulding machines. The project proves how interdisciplinary and international interaction can also be used to close material cycles where there are no comprehensive collection systems to date. “Circular Economy is a worldwide challenge with different regional focuses”, pinpointed Engleder. “With our experience from Europe, we can contribute to people taking the first steps towards circular economy in other regions of the world, such as South America or Asia. The closer enterprises cooperate along the value chain, the better this works,” he concluded.